Search

Smart Electronics TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection

Products > Battery Protection Board > Smart Electronics TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection
    • 1
    • 2
    • 3
    • 4
    • 5
    • 6

Smart Electronics TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection

TP4056 18650 lithium battery module 3.7V 3.6V 4.2V lithium battery charging board 1A overvoltage protection
shared：

Model Number
18650 tp4056
Product Name
Lithium Battery Charger Module
Maximum charging current
1000mA
Input voltage
5V
Charging cut-off voltage
4.2V ± 1%
Three interfaces
MICRO/MINI/TYPE-C
Over discharge protection voltage
2.5V
Overcurrent protection current
3A

Type 1
1A lithium battery protection MICRO interface
Type 2
TP4056 without protective MINI interface
Type 3
TP4056 without protected MICRO interface
Type 4
TP4056 with protected TYPE-C interface
Type 5
TP4056 lithium battery without protection TYPE-C

Usage:

Attention: When the battery is first connected, there may be no voltage output between OUT+and OUT -.

At this time, charging with 5V voltage can activate the protection circuit. If the battery is short circuited from B+B -

and then connected again, charging is also necessary to activate the protection circuit. When using a mobile

phone charger for input, it should be noted that the charger must be able to output 1A or above,

otherwise it may not charge properly.


The TYPE C USB base and its adjacent+- pad are the power input terminals, connected to a 5V voltage.

B+is connected to the positive pole of the lithium battery, and B - is connected to the negative pole of the

lithium battery. OUT+and OUT - connect to the load, such as the positive and negative poles of the mobile

booster board or other loads.


Connect the battery to B+B -, insert the phone charger into the USB base, the red light indicates charging,

and the blue light indicates full charge.


Name
Phone
Email
Corporate name
Address
Leaving Message*
 
Verification code
Submit

TPA3110 XH-A232 30W+30W 2.0 Channel Digital Stereo Audio Power Amplifier DC 8-26V 3A C6-001 3110 Amplifier Board

Smart Electronics HC-SR501 Adjust IR Pyroelectric Infrared PIR Motion Sensor Detector Module

HC-SR501 Adjust IR Pyroelectric Infrared PIR Motion Sensor Detector Module Automatic induction: When someone enters its induction range, enter the high level, people leave the sensor range is automatically delayed off high. Output low. 2. photosensitive control (optional): the module reserved for location, can be set to photosensitive control, strong light during the day or not induction. Photosensitive control is optional, the factory did not install photosensitive resistor. If necessary, please buy a separate photosensitive resistor to install.

NRF52832 Low Power Ble 4.2 Module 2.4G Wireless Module BLE4.0 4.2 Module

Smart Electronics JDY-16 Ble 4.2 module high-speed transparent BLE support airsync iBeacon super CC2541

JDY-16 Ble 4.2 module high-speed transparent BLE support airsync iBeacon super CC2541 Feature No byte limit for serial port transmission and reception during transparent transmission Effective communication distance within 80 meters Working temperature: -40~+80 ℃ Communication rate 8k Bytes per second Support UART and IIC communication methods Working voltage: 1.8-3.3V

Smart Electronics ESP32 WIFI BLE Single/Dual 4/8 channel Relay Module ESP32 Secondary Development Board

ESP32 WIFI BLE Single/Dual 4/8 channel Relay Module ESP32 Secondary Development Board

Smart Electronics Raspberry pi zero camera module OV5647 500W RPI zero v1.3 camera

Raspberry pi zero camera module OV5647 500W RPI zero v1.3 camera 5 million pixels Light-sensitive chips OV5647 Camera parameters: The CCD size: 1/4 inch Viewing Angle (Diagonal) : 72.4 degrees The best pixel sensor: 1080 p Static image resolution is 2592 x 1944 Support 1080 p30, 1080 p60 and 720 x480p60/90 video footage Overall size: 60 mm x 11.5 mm x 5 mm

Smart Electronics LNA 50-4000 MHz RF SPF5189 NF 0.6dB Low Noise Amplifier Signal Receiver Board Wireless Communication Module With Shield Shell

LNA 50-4000 MHz RF SPF5189 NF 0.6dB Low Noise Amplifier Signal Receiver Board Wireless Communication Module With Shield Shell Specifications: LNA: 50-4000mhz NF: SPF5189Z LNA0: 0.6 dB Amplifier: FM Size: 34 x 25mm/1.33 x1.0inch

Smart Electronics TDA7293/TDA7294 Mono Channel Amplifier Module Circuit PCB Bare Board 4XFB

TDA7293/TDA7294 Mono Channel Amplifier Module Circuit PCB Bare Board 4XFB Model: TDA7293/TDA7294 Power supply: double AC 15V to 36V (AC needs rectification and filtering) or DC positive and negative 18V to 50V.Recommended double 35V (Note that it is not a dual 35V transformer, it is positive and negative 35V DC. And It is recommended to double 26V/200W toroidal transformer, after rectification voltage is about DC double 35V).

Smart Electronics Esp-32s esp-wroom-32 Wifi Blue-tooth Board Esp32 Development Board esp 32 wroom

Esp-32s esp-wroom-32 Wifi Blue-tooth Board Esp32 Development Board esp 32 wroom Product Optional WROOM-32 WROOM-32U WROOM-32D Neutral WROOM-32 WROOM-32E

TPA3118 Mono Digital Amplifier Module Board High Sound Quality 60W

Green mini version RC522 RFID Module IC Card Proximity Module MFRC-522 RF Module with S50 Fudan Card Keychain

Smart Electronics High Power TDA3116D2 Two Channel Audio Digital Amplifier Board 12-24V 100Wx2

High Power TDA3116D2 Two Channel Audio Digital Amplifier Board 12-24V 100Wx2 Item: XH-M190 Name: Digital Audio Amplifier Model: XH-M190 The number of chips: dual-core chips Chip Name: TPA3116D2 Input power: DC12V-24V Output power: 100Wx2 Input Impedance: 51Kx2 Power efficiency:> 90% Output resistance: 4-8Ohm Frequency range: 14-100KHz Noise ratio: 100db Output channel: left and right dual channel Size: 105 * 65 * 23MM Net weight: 90g

L298N motor driver board module intelligent vehicle robot accessory H-bridge drive stepper motor driver

Smart Electronics PIR IR Light Motion Sensor Infrared Human Induction Lamp Switch 220V 50HZ Lights Control Ceiling On Off 3-6m Sensing

PIR IR Light Motion Sensor Infrared Human Induction Lamp Switch 220V 50HZ Lights Control Ceiling On Off 3-6m Sensing Product Parameter: 1.Sensing Mode:PIR sensing + light control 2.Rated Voltage:220V 50HZ 3.Output Way:Controllable Silicon 4.Load Power:filament lamp ≤100W electricity saving lamp ≤30W LED≤18W 5.Delay:20s (people are moving within the sensing range, the switch will auto delay ​and keep connecting;if people stay still,switch will stop responsing) 6.Sensing Distance:3-6m (high temperature will influence switch sensibility) 7.Sensing Angle:110° 8.Sensitivity to light :darkeness

Smart Electronics Cell Pack Module Original 3S 25A Li-ion 18650 BMS PCM Battery Protection Board With Balance For li-ion Lipo Battery

Cell Pack Module Original 3S 25A Li-ion 18650 BMS PCM Battery Protection Board With Balance For li-ion Lipo Battery

Smart Electronics HC-08 BLE4.0 master-slave integrated Bluetooth module CC2540 wireless serial communication data transmission module

HC-08 BLE4.0 master-slave integrated Bluetooth module CC2540 wireless serial communication data transmission module Product model: HC-08 Working frequency band: 2.4G Communication interface: UART3.3VTL level Working voltage: 3.0-3.6V RSSI support: not supported Communication level: 3.3V Transmission power: 4dBm Reference distance: 80 meters Air speed: 2Mbps Antenna interface: built-in PCB antenna Communication current: 0.4uA Receiving sensitivity: 85dbm@2Mbps Working humidity: 10%~90% Storage temperature: 40 ℃ -+80 ℃ Working temperature: -25 ℃ -75 ℃

Smart Electronics GY-291 ADXL345 Digital Three 3 Triple Axis Sensor Acceleration Module IIC SPI Replace ADXL335

GY-291 ADXL345 Digital Three 3 Triple Axis Sensor Acceleration Module IIC SPI Replace ADXL335 1. Adxl345 digital three-axis acceleration of gravity tilt module Ar code iic / spi. 2. Name: the adxl345 module (three-axis acceleration of gravity). 3. use the chip: the adxl345. 4. power supply :3-5v. 5. means of communication: the iic / spi communication protocol. 6. measuring range: ± 2g ± 16g. 7. schematics, manuals and reference documentation of relevant data. 8. 51, the avr, the Ar microcontroller test code. 9. 3-axis, ± 2g / ± 4g / ± 8g / ± 16g.

Smart Electronics TPA3255 mono 600W high-power full frequency/subwoofer optional fever digital power amplifier board

TPA3255 mono 600W high-power full frequency/subwoofer optional fever digital power amplifier board TPA3255 is a high-performance class D power amplifier, it has class D efficiency and can bring true high-end sound quality. The device has an advanced integrated feedback design and a proprietary high-speed gate driver error correction function (PurePath™ Ultra HD). This technology allows the device to maintain ultra-low distortion throughout the audio frequency band while exhibiting wonderful sound quality.

Smart Electronics CSR8645 Bluetooth 4.0 Low-Power Audio Module Supports High-Quality Lossless Compression Speaker Amplifier Board

CSR8645 Bluetooth 4.0 Low-Power Audio Module Supports High-Quality Lossless Compression Speaker Amplifier Board The main control chip CSR8645 stereo audio module can make calls. The headset can be connected to 2 mobile phones at the same time. CSR has better sound quality. BLE 4.0, good wall penetration effect, APT-x high sound quality transmission.

Smart Electronics Dual coil fast wireless charger transmitter module PCBA board + 2 coil general qi standard diy board

Dual coil fast wireless charger transmitter module PCBA board + 2 coil general qi standard diy board Product Parameters 1. Input power supply: 5V 2A or 9V 1.67-2a, output: 5V 1A or 9V 1.2A 2. Product weight: 0.035kg 3. Charging power: 5W / 7.5w/10w automatic identification 4. Transmission distance: 2-8mm 5. Executive standard: Qi wireless charging standard 6. Product certification: CE / FCC / RoHS
Previous： Smart Eletronics Universal Wireless Charging PCBA Coil Charging Pcb Circuit Board Qi Wireless charger receiver module
Next： Smart Electronics HC-05 master-slave integrated BlE module DIY wireless serial port transparent electronic module BLE
Return
TOP
86-755-83877216
smartbes
smartbes